lmm@magnesiacarbonbricklmm.com

Technical support and construction service team

Analysis of the Causes and Improvement Measures for Steel Leakage Between the Ladle Sliding Nozzle and the Upper Slide Plate

The ladle sliding nozzle, composed of the upper nozzle, upper slide plate, lower slide plate, and lower nozzle, is the channel through which molten steel enters the tundish from the ladle, serving to seal the steel flow and regulate the flow rate. Through related technological improvements, the service life of the ladle upper nozzle has been continuously extended, and the slide plate can now be used in multiple furnaces consecutively, reducing consumption, increasing production efficiency, and reducing the labor intensity of workers, providing strong conditions for the advancement of steelmaking technology. However, with the increase in the service life of the sliding nozzle, the risk of steel leakage between the upper nozzle and the upper slide plate is also increasing, seriously threatening the safety of personnel and equipment. Therefore, this paper analyzes the factors affecting steel leakage between the upper nozzle and the upper slide plate and formulates corresponding improvement measures to improve the safety of the upper nozzle and the upper slide plate and reduce the accident rate in steel plants.

Part 1. Causes of Steel Leakage Between the Upper Nozzle and the Upper Slide Plate

The upper nozzle and the upper slide plate are connected by a male-female joint and a fire-plaster or putty gasket, serving to seal the molten steel. Its structure is shown in Figure 1. The direct cause of molten steel leakage between the inlet and the upper slide plate is a gap that forms between them. Under static pressure, molten steel leaks out through this gap, causing the accident. The main reasons for this gap include: incorrect operation, deformation of the mechanism, and damage to the inlet or upper slide plate.

Analysis of the Causes and Improvement Measures for Steel Leakage Between the Ladle Sliding Nozzle and the Upper Slide Plate

1.1 Incorrect Operating Procedures

(1) Incorrect or Excessive Installation of the Water Inlet. The water inlet is installed inside the base brick. If the water inlet is installed incorrectly or too deeply, uneven or excessively large mud joints will occur. When the mud joints are uneven, the upper slide plate and the water inlet cannot be tightly pressed together on the side with the larger mud joint, and molten steel can easily leak out from the side with the larger mud joint during steel pouring. If the mud joint is large, the fire mud between the upper slide plate and the water inlet will be less stressed, relatively loose, and have a high porosity. After long-term erosion, annular grooves will form, and a certain degree of erosion will cause steel penetration, resulting in equipment damage or even accidents that injure operators.

(2) The fire mud is too thin or the mud layer is too thick. If the fire mud is too thin, its fluidity is too strong, and it cannot fill the gap between the upper slide plate and the water inlet, resulting in an unsealed mud joint. Once there are incomplete or damaged parts, molten steel will seep out from the weak parts during steel pouring, which can cause steel leakage accidents in severe cases. Furthermore, excessively thick mud layers also affect the use of sliding nozzles. Fire clay has a high shrinkage rate; the thicker the fire clay, the greater the shrinkage after sintering. This shrinkage creates gaps between the sliding plate and the nozzle, allowing molten steel to seep out and causing leakage.

(3) Inadequate cleaning of the upper nozzle surface. Upper nozzles are typically used multiple times, with lifespans ranging from 5 to 30 times. The longer the service life of the upper nozzle, the more frequently it needs cleaning. If it is not cleaned properly, residual steel or particulate impurities in the fire clay will act as a support, causing insufficient compaction of the fire clay between the upper nozzle and the upper sliding plate. Under immense static pressure, molten steel will leak out between the upper nozzle and the upper sliding plate.

(4) During the first use of the upper nozzle, if the ladle lining temperature is too low, the upper nozzle will creep into the inner cavity of the seat brick. When installing the upper nozzle, apply an appropriate amount of fire clay to the outer surface, squeeze the nozzle brick into the lower seat brick, and then install the upper and lower sliding plates and close the mechanism. If the ladle is used without preheating, the low lining temperature will prevent the molten ladle lining from hardening quickly. If a sliding plate is installed in this condition, the inlet will shift towards the base brick under spring pressure. This increases the gap between the inlet and the sliding plate, leading to poor sealing and steel leakage.

1.2 Mechanism Deformation

The ladle bottom mounting plate or support may be severely deformed. If the ladle bottom is too close to the molten ladle surface during pouring, the bottom and mechanism will be subjected to prolonged heat radiation from the molten steel, causing deformation. This deformation will generate stress on the inlet and sliding plate. This stress, acting on the inlet and sliding plate in opposite directions, can cause misalignment. If this stress causes displacement, the molten ladle lining will loosen, resulting in steel leakage.

1.3 Damage to the Inlet and Sliding

After repeated use, the inlet will develop a decarburized layer inside the orifice due to repeated oxygen burning. This loose layer accelerates erosion of the inlet. The thin wall of the inlet gate causes damage to the joint between the upper and lower plates during cleaning. The more cleanings are performed, the more severe the damage becomes. If not carefully observed, severe damage to the joint between the upper plate and the inlet gate can lead to steel leakage.

1.4 Mismatch between the upper plate and the mechanism dimensions

If the upper plate is too small, it will wobble within the sliding box. After repeated use, the lubricant on the plate surface will wear off, and peeling, steel trapping, and corrosion may occur. When the upper plate is pulled, the friction between the plates is high. If the upper plate is too small and does not match the mechanism cavity, there will be a large gap between the upper plate and the inner cavity. Under the action of the friction between the plates, the upper plate will wobble within the mechanism cavity, causing damage to the sealant between the upper plate and the inlet gate, leading to steel leakage.

Part 2. Improvement Measures

(1) Use a sprue installation tool to install the sprue. After installation, the end face of the sprue should be flush with or 1-2mm concave to the plane of the slide plate mounting base. After installation, use a locator to firmly hold the sprue in place until the sprue hardens and no longer moves backward. Bake the sprue to ensure it is completely dry and the sprue position is fixed before installing the slide plate.

(2) Before using the sprue, ensure it is of moderate hardness, plastic but does not flow under vibration, free of impurities, dry powder lumps, hardened interior, and hardened surface.

(3) Install a cooling system and heat insulation plates on the mechanism to cool and insulate it, preventing overheating and deformation of the mechanism and ladle bottom, which could cause leakage due to external forces on the slide plate and sprue. Regular maintenance and inspection of the mechanism and ladle bottom are also necessary to ensure they meet usage requirements.

(4) Minimize the carbon content as much as possible while ensuring the sprue’s thermal shock resistance. Simultaneously, the density of the upper water inlet is improved to prevent the upper water inlet from becoming loose and peeling off due to repeated use and oxygen burning.

(5) A reasonable sliding plate size is designed to prevent the sliding plate from shaking inside the mechanism. In addition, the mechanism is equipped with a clamping device to fix the sliding plate, ensuring it remains fixed within the sliding box and preventing shear force on the mud joint, which could cause the fire mud to become loose and damaged.

Part 3 Conclusion

By standardizing the installation and operation of the sliding water inlet, improving the mechanism and equipment, and enhancing the quality of the upper water inlet and upper sliding plate, actual use in steel plants has shown that steel leakage accidents between the upper water inlet and upper sliding plate have been significantly reduced, eliminating the previous frequent occurrence of direct steel leakage between the upper water inlet and upper sliding plate, thus providing a guarantee for safe production.

LMM YOTAI established in 2007. Our production technology comes from Japanese Yotai. As an experienced and international player in the refractories industry. We have succeeded in expanding both the breadth of its product range and the depth of its services. From raw material selection, refractory portofio & optimization, installation & services & recycle of used refractories on site to further reduce client’s Opex & Capex in refractory consumption per ton steel output, meanwhile improve product quality of client.

Our Product have been supplied to world’s top steel manufacturer Arcelormittal, TATA Steel, EZZ steel etc. We do OEM for Concast and Danieli for a long time

Facebook
LinkedIn
Pinterest
Reddit

Comprehensive solution of Refractory for steelmaking

Fill out the form below, and we will be in touch shortly.
Contact Information