lmm@magnesiacarbonbricklmm.com

Technical support and construction service team

GOR Converter Refractory Lining Selection for Stainless Steelmaking

What Is a GOR Converter?

The GOR converter is mainly used in stainless steelmaking and foundry applications. At present, GOR converters with nominal capacities of 1.5 t, 5 t, 10 t, and 60 t are widely used in industrial production. This refining process adopts converter composite blowing technology to produce stainless steel, and its equipment configuration and metallurgical process are similar to the KiBOP, STP, and other stainless steel refining processes used in Europe and Japan.

Compared with traditional AOD refining, the GOR converter significantly improves tuyere life through its dual-blowing converter process, resulting in a longer furnace campaign life. The steel grades produced by the GOR converter are mainly non-ultra-low-carbon stainless steels. Although the early furnace campaign life was relatively low due to process limitations, continuous optimization and refractory upgrades have greatly improved operational stability and lining service life. However, several refractory lining challenges still require further optimization.

The GOR converter is a bottom-blown stainless steel converter that uses multiple energy media for composite blowing. A mixed gas composed of nitrogen, oxygen, argon, and natural gas with adjustable ratios is injected into the molten bath through three sleeve-type tuyeres installed at the converter bottom.

Like other stainless steel refining converters, the GOR process is divided into three blowing stages:

  • Stage 1: Oxygen blowing with hydrocarbon protection for the tuyere area
  • Stage 2: Blowing of oxygen, argon (or nitrogen), hydrocarbons, and mixed gases
  • Stage 3: Pure argon or nitrogen blowing for final refining and bath stirring

The GOR converter adopts a bottom-blowing design with a hydraulic furnace bottom and movable furnace bottom system, greatly reducing maintenance time. Furnace lining construction usually requires about 16 hours, while demolition takes around 8 hours. In contrast, AOD furnaces generally use side-bottom blowing or top-bottom combined blowing with a fixed furnace bottom structure.

Cross-section of a GOR converter showing magnesia carbon brick lining, tuyere zone, slag line, and furnace bottom refractory materials.

Comparison Between GOR Converter and AOD Converter

Fixed Investment and Refractory Consumption

From the perspective of fixed investment, the initial equipment investment for a GOR converter is relatively high. The furnace shell is larger, and the overall refractory material consumption is also higher compared with an AOD converter.

However, despite the higher refractory consumption, the GOR process provides advantages in stainless steel refining flexibility and raw material adaptability.

Smelting Cost Advantages

The AOD furnace requires strict control of raw material composition and usually depends on electric furnace molten stainless steel scrap. In contrast, the GOR converter has lower requirements for raw materials and can use a larger proportion of high-carbon ferrochrome, significantly reducing the consumption of expensive low-carbon and micro-carbon ferrochrome alloys.

During the first blowing stage, the GOR converter uses hydrocarbon cooling technology and does not require argon or nitrogen cooling tuyeres. As a result, argon consumption is generally lower than that of an AOD converter. When producing J-series stainless steel, only a small amount of argon is needed.

Another important advantage is the accurate control of nitrogen content in molten steel by bottom nitrogen blowing.

GOR Converter Production Process Characteristics

Compared with the AOD process, the GOR converter has lower requirements for the composition of molten steel from the electric furnace. Typically:

  • Carbon content is above 3%
  • Silicon content is above 0.2%

Because of its large furnace capacity ratio, the GOR converter achieves a faster decarburization rate and better degassing performance than the AOD furnace.

The bottom-blowing tuyeres are positioned close to the furnace centerline, resulting in reduced furnace vibration during operation. By contrast, AOD converters often produce noticeable platform vibration during blowing.

Unlike AOD refining, the GOR process does not require slag removal during blowing. Tapping is performed through a tapping hole, which improves slag-metal separation and helps control slag carryover into the ladle. This is particularly beneficial for alloying easily oxidized elements such as titanium.

However, the addition of a tapping hole increases the complexity of furnace lining construction.

Although the theoretical blowing time of the GOR process is short, large amounts of cooling scrap and fluxes must be added during refining, extending the actual blowing time. Excessively high molten steel temperatures can accelerate refractory lining wear and slag erosion.

Process Control Characteristics of GOR Converters

AOD converter systems generally use fully automated process control from the beginning of refining, and the software system is highly mature.

In comparison, the GOR converter allows manual intervention during the initial blowing stage. Once the carbon content decreases to approximately 0.25%, the process switches to automatic control.

This semi-automatic control strategy makes the GOR process more adaptable to plants with fluctuating raw material conditions and varying hot metal quality.

The GOR converter can efficiently complete:

  • Decarburization
  • Deoxidation
  • Degassing
  • Alloying
  • Optional dephosphorization

Because the mixed gas composition can be adjusted over a wide range, the process can use molten steel from electric arc furnaces, induction furnaces, or other melting systems.

Currently, stainless steel produced by GOR converters is widely used for:

  • Hot rolled strip
  • Narrow strip
  • Seamless steel pipe
  • Bars and wire rods
  • Complex forgings

These products exhibit excellent processing performance and stable metallurgical quality.

Selection of Refractory Materials for GOR Converters

Selection of Shaped Refractory Materials

Due to the long refining cycle and high operating temperature of the GOR converter, large quantities of lime and scrap steel are added during the process for cooling purposes. This causes severe impact and abrasion in the charging area of the furnace body.

Therefore, the converter lining refractory must provide:

  • High hot strength
  • Excellent thermal shock resistance
  • Strong slag corrosion resistance
  • Good structural stability at elevated temperatures

Since slag basicity changes from low to high during refining, the slag line area requires refractory materials with strong resistance to both low-basicity and high-basicity slag attack.

After repeated industrial testing and production verification, magnesia-calcia refractories have proven suitable for the shaft area of the GOR converter.

Because large volumes of gas are injected through the three bottom tuyeres, the refractory materials in the tuyere zone are subjected to severe erosion from high-temperature molten steel and slag. Residual slag after tapping also accumulates at the furnace bottom.

As a result, the furnace bottom refractory lining requires:

  • Excellent high-temperature strength
  • Superior thermal shock resistance
  • Low thermal expansion
  • Strong resistance to slag penetration and corrosion

In many stainless steel refining operations, high-performance magnesia carbon bricks are also used in critical wear areas because of their excellent thermal shock resistance and slag resistance.

Magnesia carbon bricks, magnesia-calcia refractory bricks, ramming mass, and magnesia powder used in stainless steel converter linings.

Selection of Monolithic Refractory Materials

Furnace Brick Joint Filling

During furnace lining installation, the horizontal and vertical joints between refractory bricks can be filled using 0.5–0 mm magnesia powder.

Furnace Mouth and Tapping Hole Repair Materials

The gaps around the furnace mouth and tapping hole can be filled with refractory plastic materials based on magnesia or high-alumina compositions.

Furnace Bottom Joint Materials

For the joint between furnace bottom bricks and furnace body bricks after bottom closure, high-quality ramming materials are recommended. Suitable materials include:

  • Magnesia ramming mass
  • Magnesia-chrome ramming material

Annular Joint Materials for Exchangeable Furnace Bottoms

The annular joint between the exchangeable furnace bottom and furnace body is difficult to maintain and experiences severe slag attack.

The selected monolithic refractory should therefore possess:

  • Good sintering performance
  • Excellent hot strength
  • High resistance to high-basicity slag corrosion

Suitable materials include:

  • Magnesia-calcia refractory materials
  • High-purity magnesia-based materials
Bottom-blown tuyere zone inside a GOR converter with refractory lining designed for molten steel erosion resistance.

Conclusion

As stainless steel production increasingly demands higher refining efficiency, lower alloy consumption, and longer furnace campaign life, the GOR converter has become an important technology in modern stainless steelmaking. Compared with traditional AOD refining, the GOR process offers advantages in raw material flexibility, nitrogen control, decarburization efficiency, and alloy recovery.

However, due to the severe operating conditions inside the converter — including high-temperature molten steel impact, complex slag chemistry, and intense bottom blowing — the selection of suitable converter refractory lining materials is critical to furnace performance and operational stability.

High-quality magnesia carbon bricks, magnesia-calcia refractories, and durable monolithic refractory materials play a key role in improving refractory service life, reducing shutdown frequency, and lowering overall steelmaking costs. Proper refractory configuration for the shaft area, slag line, tuyere zone, and furnace bottom can significantly enhance campaign life and production efficiency.

For stainless steel plants seeking stable operation and lower refractory consumption, optimizing the GOR converter lining design remains an essential direction for future refractory technology development.

FAQ

1. What is a GOR converter used for?

A GOR converter is mainly used for stainless steel refining and foundry applications. It performs decarburization, degassing, alloying, and nitrogen control through bottom composite blowing technology.

2. How is a GOR converter different from an AOD converter?

Compared with an AOD converter, a GOR converter offers lower argon consumption, greater raw material flexibility, faster decarburization, and improved nitrogen control.

3. What refractory materials are commonly used in GOR converters?

Common refractory materials include magnesia-calcia refractories, magnesia carbon bricks, magnesia ramming mass, and monolithic refractory materials.

4. What are the main causes of refractory wear in GOR converters?

Major causes include high-temperature molten steel erosion, slag corrosion, thermal shock, scrap impact, and intense gas stirring from bottom blowing tuyeres.

5. How can the service life of a GOR converter lining be improved?

The lining life can be improved through optimized refractory selection, proper slag control, better cooling practices, and the use of high-quality slag-resistant refractory materials.

6. Why are magnesia carbon bricks important in converter linings?

Magnesia carbon bricks provide excellent thermal shock resistance, slag corrosion resistance, and high-temperature stability, making them suitable for severe wear zones in stainless steel converters.

LMM YOTAI established in 2007. Our production technology comes from Japanese Yotai. As an experienced and international player in the refractories industry. We have succeeded in expanding both the breadth of its product range and the depth of its services. From raw material selection, refractory portofio & optimization, installation & services & recycle of used refractories on site to further reduce client’s Opex & Capex in refractory consumption per ton steel output, meanwhile improve product quality of client.

Our Product have been supplied to world’s top steel manufacturer Arcelormittal, TATA Steel, EZZ steel etc. We do OEM for Concast and Danieli for a long time

Facebook
LinkedIn
Pinterest
Reddit

Comprehensive solution of Refractory for steelmaking

Fill out the form below, and we will be in touch shortly.
Contact Information