lmm@magnesiacarbonbricklmm.com

GOR Refractory Lining Solutions

A GOR (Gas-Oxygen Refining) converter lining must withstand intense bottom gas injection, high-temperature molten steel and slag attack, thermal cycling, and localized wear around the bottom-blowing tuyeres and slag-contact zones. LMM YOTAI develops furnace-specific refractory systems by matching materials and lining design to local service conditions.

Request a tailored GOR lining proposal
Since 2007Established specialist
90+Countries served
Integrated scopeBrick · Monolithic · Functional
Furnace-specificLining design

How GOR Converter Lining Design Affects Campaign Life and Refractory Cost

Refractory cost per ton depends on campaign life, wear distribution, repair practice and material cost — not brick price alone.

GOR lining cost per ton is strongly influenced by campaign life, bottom-tuyere durability and the distribution of wear across the furnace bottom and working lining. Localized wear can develop around the bottom-blowing tuyere zone, while slag corrosion, thermal cycling, molten-steel flow and operating practice also affect refractory consumption. Dedicated tuyere-area grades, zone-based material selection and targeted repair are therefore used together rather than relying on a single refractory grade throughout the vessel.

GOR Service Conditions & Lifecycle Management

A GOR converter combines top-and-bottom combined blowing, so it carries both lance and bottom gas-injection duties.

GOR refractories see concentrated thermal, chemical and mechanical load at the bottom-blowing tuyere zone, while the barrel, slag line and other bottom areas see different duties. Blowing practice, tuyere arrangement, slag chemistry and steel grade define the refractory environment, so GOR lining selection is zoned across the tuyere, bottom, barrel and slag-contact zones.

Lifecycle management

Beyond grade selection, how the lining is operated and maintained is an important factor in campaign life.

Campaign-life management

Wear monitoring, repair timing and zone-specific maintenance help extend GOR campaign life without unnecessarily increasing lining thickness or material consumption.

Bottom-tuyere control

Bottom-tuyere condition is monitored because gas injection creates concentrated thermal, chemical and mechanical loads around the tuyere and adjacent furnace-bottom areas.

Repair and maintenance strategy

Gunning, ramming or local patching can be selected according to observed wear, remaining lining thickness and operating requirements.

Lining performance feedback

Campaign results are reviewed against wear patterns, operating conditions and refractory consumption to refine the next lining design.

GOR Converter Zone-Based Lining Design

Grade selection follows the zone — not a single brick for the whole vessel. Each zone sees a different mix of temperature, slag and mechanical load.

Zone / componentKey service conditionsTypical wear mechanismsMaterial approach
Safety liningPermanent shell protection; mainly exposed to penetration and thermal loadPenetration, thermal loadMagnesia brick (MZ-91, permanent backing)
Tuyere / tuyere areaBottom gas injection, high local thermal and mechanical load, slag and molten-steel contactErosion, corrosion, thermal shockDedicated MgO-C (MGT-8A) where an MgO-C system is appropriate
Other bottom areaBath contact, moderate agitationCorrosion, erosionZone-selected MgO-C (MGT-8B, MGT-8C) or other compatible basic refractory systems
Barrel / upper coneSlag splash, thermal cyclingErosion, thermal cyclingZone-selected MgO-C (MG-20A) or other compatible basic refractory
Slag-contact zoneRepeated slag contact and thermal cyclingSlag corrosion, erosionZone-selected basic refractory or monolithic repair material (e.g. MT-12A)
Bottom repair / monolithic zonesThermal cycling, metal and slag contactCorrosion, erosion, thermal shockRamming and repair materials (DY-1, D-6, TC-1)

Note: The grade codes shown above are LMM YOTAI internal product grades and are not universal industry standards. Final grade selection is matched to furnace geometry, steel grades, slag practice, operating conditions and previous wear patterns.

Critical wear zones — The bottom-blowing tuyere and adjacent furnace-bottom areas require particular attention because gas injection creates concentrated thermal, chemical and mechanical stresses. Actual wear distribution depends on tuyere arrangement, gas flow, slag chemistry, steel grade, furnace-bottom design and operating practice. A dedicated tuyere-area grade such as MGT-8A may therefore be used within an MgO-C-based system, while adjacent bottom and working zones are graded according to their individual service conditions.

Material families

The GOR Converter lining system normally combines working and safety linings with selected monolithic and shaped or prefabricated refractory components according to vessel design and operating practice.

In a GOR vessel, magnesia-carbon, magnesia-calcia and other compatible basic refractory systems may be used across the working lining, with grades selected according to local wear conditions. Dedicated grades can be specified around the tuyere zone, while other bottom, barrel and slag-contact areas are matched to their individual thermal and chemical duties. Where MgO-C is applied, explore our magnesia carbon brick range.

Working & permanent lining

Magnesia carbon brick (working lining)Example zone-graded arrangement: MGT-8A at the tuyere and MG-20A in selected barrel areas, subject to operating conditions.
Magnesia calcium brickUsed in selected working-lining zones where low-carbon steelmaking requirements and refractory/slag compatibility favor a low-carbon basic refractory system.
MgO-Cr2O3 brickConsidered for selected high-wear zones where slag chemistry and operating conditions are compatible.
Magnesia brick (safety lining)MZ-91 permanent backing protecting the shell.

GOR Functional Refractories & Tapping Components

Functional refractories and tapping components support controlled steel flow, bottom stirring and slag retention during GOR operation.

FunctionalConverter slide gate plateTapping-control component for GOR vessels equipped with a compatible sliding-gate system. LMM YOTAI Converter Slide Gate Plates are supplied in alumina-mullite, Al-C and ZrO2 grades with matched mechanisms (LMM-201 / 301 / 401 / 501) for different converter sizes.
FunctionalConverter porous plug brickBottom-blowing functional refractory for vessels equipped with a compatible gas-injection system. LMM YOTAI porous plug bricks (PP-A / PP-B / PP-C series) are supplied for GOR vessels equipped with a compatible porous-plug or gas-injection system.

What We Need to Design the GOR Converter Lining

The more operating data you share, the closer the proposal matches your vessel.

Furnace geometry and vessel size (working volume, bottom design and tuyere layout).
Steel grades and production mix (stainless-steel grades, carbon range, alloy content and special-steel grades).
Slag chemistry and basicity (FeO, CaO/SiO2, MgO and Al2O3 content, oxidation state).
Blowing practice and bottom-tuyere parameters (gas flow, oxygen rate, stirring intensity).
Tap temperature and thermal profile.
Previous campaign and reline history, including wear maps, remaining lining profiles and failure points.
Refractory budget and target campaign life.
Maintenance and repair capability (gunning, ramming and hot-repair windows).

LMM YOTAI GOR Converter Refractory Solution

For GOR Converter applications, LMM YOTAI combines furnace-specific lining design with coordinated supply of brick, monolithics and shaped or prefabricated refractory components across the full refractory scope.

Engineering

Furnace-specific lining design, zone mapping and reline support.

Material coordination

Matched grades across brick, monolithics and shaped or prefabricated refractory components.

Supply

Coordinated production, inspection and delivery across the full refractory scope.

Technical support

Installation guidance, repair recommendations and campaign follow-up.

Trusted by steelmakers worldwide

Get a tailored GOR Converter lining proposal

LMM YOTAI engineers spec each lining to your furnace and steel grades, then supply brick, monolithics, functional refractories and installation materials as one coordinated package.

Request a proposal

Frequently asked questions

Practical questions from operators specifying a new GOR Converter lining or reline.

A dedicated MgO-C grade such as MGT-8A may be specified for the bottom-blowing tuyere area, while other zones are selected according to their individual thermal, chemical and mechanical duties.

The bottom-blowing tuyere and adjacent furnace-bottom areas can experience particularly severe localized wear because gas injection creates concentrated thermal, chemical and mechanical loads. Actual wear patterns depend on tuyere layout, gas flow, slag chemistry and operating practice.

Tuyere grade selection starts with tuyere design, gas flow, steel grade, slag chemistry, thermal cycling and previous wear patterns. Where an MgO-C system is appropriate, LMM YOTAI may specify MGT-8A for the tuyere/tuyere-area zone and different grades for adjacent bottom areas.

Tuyere-grade selection, blowing-practice control, slag-chemistry management and scheduled gunning/ramming repair are the main levers.

Yes. We supply brick, monolithics (MT-12A, DY-1, D-6, TC-1) and installation materials together, plus engineering support for lining design and reline.

Related furnace solutions

Lining systems for the rest of the steelmaking route.

SolutionEAFLining system & zone-to-grade map
SolutionBOF ConverterLining system & zone-to-grade map
SolutionLadle & LFLining system & zone-to-grade map
SolutionAOD ConverterLining system & zone-to-grade map
SolutionVOD / VODCLining system & zone-to-grade map
SolutionRH DegasserLining system & zone-to-grade map

Refractory Catalogue & Grade Datasheets

Full grade datasheets and the LMM YOTAI refractory brochures support specification and reline planning.

BrochureRefractory Materials Main brick & monolithic grades
BrochureFunctional Refractories Slide Gate & Nozzle
BrochureGraphite ElectrodeElectrode scope

Comprehensive solution of Refractory for steelmaking

Fill out the form below, and we will be in touch shortly.
Contact Information