lmm@magnesiacarbonbricklmm.com

Technical support and construction service team

Performance of magnesia and chromite for magnesia-chrome bricks

The refractory raw materials for magnesia-chrome refractories are mainly composed of magnesia and chromite. The performance of the raw materials is as follows:magnesia chrome bricks

magnesia chrome bricks
magnesia chrome bricks

Performance of magnesia

Magnesia-chrome refractories are sintered refractory materials made from magnesia and chromite. To be familiar with the characteristics of this material and use it reasonably, you need to start with magnesia and chromite.

(1) Chemical properties of magnesia

The main mineral in magnesia is periclase MgO, which is also one of the common minerals in cement clinker. Periclase can coexist with the four main minerals in cement clinker, C3S, C2S, C3A, and C4AF. Therefore, periclase has excellent corrosion resistance to cement clinker.

(2) Physical properties of magnesia

Periclite is an isometric mineral with a hardness of 6, a relative density of 3.58, a melting point of up to 2800℃, a thermal expansion coefficient of 13.5×10-6/K from 0 to 1000℃, and a thermal conductivity of 3.39 to 4.19W/(m·K) from 100 to 1000℃. These physical properties often cause the following phenomena to occur in magnesia refractory materials in cement rotary kilns.

① The melting point of periclase is very high, which makes many magnesia refractory materials have good high temperature resistance.

② Periclite has good thermal conductivity. When high-MgO refractory materials are used and the kiln lining cannot be hung, the surface temperature of the kiln body rises. At this time, not only is the heat dissipation loss very large, but it is also easy to burn the cylinder.

③ The high thermal expansion coefficient of periclase causes the insufficient thermal shock resistance of magnesia refractory materials. During use, magnesia refractory materials often peel off.

At first, magnesia refractory materials were also tried in cement rotary kilns, but due to the aforementioned problems, the use effect was not good, and magnesia bricks were soon replaced by other refractory materials.

Properties of chromite

Chromite is a natural mineral with a general chemical formula of (Mg, Fe)(Cr, Al, Fe)2O4. It is an isometric mineral with n=2.07~2.16, relative density 4.0~4.8, and hardness 5.5~5.7.

In chromite, there is a wide range of substitutions between Cr2O3, Al2O3, and Fe2O3 in R2O3, and between FeO and MgO in RO. The main minerals are pure chromite FeO·Cr2O3, magnesium chromite (Mg, Fe)O·Cr2O3, aluminum chromite FeO·(Cr, Al)O3, and iron-rich chromium spinel (Mg, Fe)O·(Cr, Al)2O3. The Cr2O3 content of chromite for refractory materials is 30%~60%.

In chromite, Fe exists in two forms, Fe2+ and Fe3+, but Fe2+ is the main form. When the temperature rises, in an oxidizing atmosphere, Fe2 in chromite will be oxidized to Fe3′ and expand in volume. In a reducing atmosphere, Fe3+ in chromite will be reduced to Fe2+. If Fe2+ is oxidized to Fe3+ and expands too much, or the redox reaction between Fe2+ and Fe3+ occurs repeatedly, the structure will become loose, and in severe cases, the refractory material will be damaged.magnesia chrome bricks

FAQ

Q1: What are the primary functions of Magnesia and Chromite in Magnesia-Chrome bricks?

A: Magnesia (MgO) provides a high melting point and excellent resistance to basic slag. Chromite (Cr2O3) enhances volume stability at high temperatures, improves thermal shock resistance, and provides superior resistance to acidic and neutral slags. The combination creates a synergistic effect through the formation of magnesia-chrome spinel.

Q2: Why is the SiO2 content so important in choosing raw materials for these bricks?

A: Low SiO2 content (typically <1.5%) is crucial. High silica leads to the formation of low-melting-point silicate phases (like monticellite), which weaken the brick’s structure at high temperatures. Reducing silica allows for “direct bonding” between magnesia and chromite grains, significantly increasing the load-softening temperature.

Q3: In which industries are Magnesia-Chrome bricks most commonly used today?

A: They are primarily used in the non-ferrous metallurgical industry (especially for copper, nickel, and lead smelting furnaces like Ausmelt or Isasmelt furnaces) and in the burning zones of cement rotary kilns. They are also used in secondary refining vessels like RH degassers and VOD furnaces.

Q4: What is the difference between Direct-Bonded and Rebonded Magnesia-Chrome bricks?

A: Direct-bonded bricks are made from high-purity magnesia and chrome concentrate fired at very high temperatures (>1700°C). Rebonded (or fused-grain) bricks use crushed electro-fused magnesia-chrome grain as raw material, offering even higher density and slag resistance, but with different thermal shock characteristics.

Q5: How does the ratio of Magnesia to Chromite affect performance?

A: Increasing magnesia content generally improves resistance to basic slags, while increasing chromite content improves thermal shock resistance and resistance to slag penetration. The optimal ratio depends on the specific furnace atmosphere and slag chemistry (Basic or Acidic).

LMM YOTAI established in 2007. Our production technology comes from Japanese Yotai. As an experienced and international player in the refractories industry. We have succeeded in expanding both the breadth of its product range and the depth of its services. From raw material selection, refractory portofio & optimization, installation & services & recycle of used refractories on site to further reduce client’s Opex & Capex in refractory consumption per ton steel output, meanwhile improve product quality of client.

Our Product have been supplied to world’s top steel manufacturer Arcelormittal, TATA Steel, EZZ steel etc. We do OEM for Concast and Danieli for a long time

Facebook
LinkedIn
Pinterest
Reddit

Comprehensive solution of Refractory for steelmaking

Fill out the form below, and we will be in touch shortly.
Contact Information